Showing 100–110 of 431 results

The SmartRack 42U Standard-Depth Rack Enclosure Cabinet protects sensitive electronic equipment from harsh conditions that would overwhelm a typical rack enclosure, including falling dirt, dust, drips and splashes. It is ideal for use in factories, construction areas, utility plants, warehouses and other areas high in moisture, dust and debris. It can protect your equipment from falling dirt, dust, drips, splashes and accidental contact with personnel.The front and rear doors have ventilating louvers instead of open mesh. They also have a sealing gasket around the door frames. On the front door there are built-in dust filters as well as fans. The filters are removable and they can be replaced with standard furnace filters - they're simple, inexpensive and effective. To compensate for the added air resistance of the filters, there are 12 large, high performance fans on the front door. The fans effectively create positive air pressure within the rack, mimicking the same type of environment one would find within a commercial clean room. Positive air pressure prevents dust from penetrating even the smallest cracks of the enclosure. The roof of the enclosure is sealed with a cap that keeps drips and falling dirt from getting inside the enclosure. Since the doors and top are sealed, cable access is provided through 6 cable ports - 2 in the roof, 2 below the rear door, and 2 in the unit floor. They allow cables to pass through, but they block the area around the cables maintaining  protection.The enclosure may be subjected to extreme vibrations and movements produced by vehicles and machinery. The heavy-duty steel frame supports up to 3000 lbs (1360.8 kgs). The large-diameter industrial casters also support up to 3000 lbs (1360.8 kgs), which means you can move the enclosure fully loaded. This is useful where you can install all your equipment in a clean environment, close the enclosure and wheel it to the dirty environment with all your equipment already protected.After the enclosure is in place, the levelers allow you to compensate for minor floor variations and make sure everything is stable. If you need to build a data center in the middle of your factory floor, you can do it with this enclosure. It's perfect for locations like factories, power stations, construction areas, shipping facilities, warehouses, processing plants, transport hubs and anywhere you need to protect equipment in a harsh working environment.

The SRWO8U22MD SmartRack 8U/12U/22U Expandable Very Low-Profile Wall-Mount 2-Post Open-Frame Rack is ideal for storing patch panels and other shallow equipment in secure IT areas with limited floor space. Mounted to the wall or resting on the floor, this rack offers fast, easy access to network components and cabling. It's compatible with EIA-standard 19-inch rack equipment that supports two-post mounting and a maximum mounting depth of 11.5 inches.Constructed from heavy-duty steel in a durable black powder-coated finish, the open-frame rack has a maximum load capacity of 150 lbs (68 kgs). The expandable design allows you to assemble the rack in an 8U, 12U or 22U configuration to meet your current needs, while leaving rack space in reserve for future expansion. It saves precious space and allows IT managers easy access for organizing, installing and servicing equipment and cabling.The rack is easy to assemble using the included hardware. The vertical mounting rails have threaded 12-24 holes for securing equipment to the steel frame.

The B070-008-19 KVM Switch gives you a rack-mountable full keyboard, LCD and touchpad in a single console that occupies only 1U of rack space. Easy to install and use, it’s the optimal solution for controlling up to eight computers/servers.The B070-008-19 uses inexpensive, user-supplied Cat5e/6/6a and a Server Interface Unit so you can control computers/servers located up to 100 feet away from the switch. You can switch easily between the ports using an on-screen display (OSD) or keyboard hot key commands. Multi-level password protection prohibits unauthorized users from accessing the connected computers. The built-in 19-inch LCD screen supports video resolutions up to 1366 x 768.The B070-008-19 stores neatly in a rack drawer and pulls out when needed. This KVM console is compatible with all major operating systems. Heavy-duty steel housing stands up to frequent use. Complies with the Federal Trade Agreements Act (TAA) for GSA Schedule purchases.Note: B051-000 remote access IP unit is not compatible with the B070-008-19 or B070-016-19 NetCommander® Cat5 1U Rack-Mount Console KVM Switch Series.

The B040-008-19 KVM Switch gives you a rack-mountable keyboard, LCD and touchpad in a single console that occupies only 1U of rack space. Easy to install and use, it’s the cost-effective solution for controlling up to eight directly connected computers/servers.The B040-008-19 has a built-in 19-inch LCD screen that supports video resolutions up to 1366 x 768. You can switch easily between the ports using on-console push buttons, an on-screen display (OSD) or keyboard hotkey commands. Password protection prohibits unauthorized users from accessing the connected computers.With this KVM switch, you can increase the number of connected computers up to 248 by daisy-chaining up to 15 B042-Series KVM switches. Uses P780-Series combo cable kits that support both PS/2 and USB connections without the need to purchase additional cables or adapters. An extra HD15 port allows an additional VGA monitor or an external console to be connected. Add a B051-000 IP Remote Access Unit to connect from anywhere in the world. When not in use, the B040-008-19 stores neatly in a rack drawer and pulls out when needed. This KVM console is compatible with all major operating systems. Rugged steel housing stands up to frequent use. Complies with the Federal Trade Agreements Act (TAA) for GSA Schedule purchases.

The SRW12USNEMA SmartRack 12U NEMA 12 Switch-Depth Wall-Mount Rack Enclosure Cabinet is designed to house EIA-standard 19-inch rack equipment in harsh, dirty work environments with limited floor space, such as factories, construction areas, utility plants, power stations, transportation terminals, distribution hubs and warehouses. Constructed from heavy-duty steel with a durable black powder-coated finish, the cabinet has a maximum load capacity of 90 kgs (200 lbs.) The SRW12USNEMA has a NEMA 12 (IP54) protection rating, protecting sensitive equipment against dirt, dust, lint, oil, drips and splashes. Its built-in air filter, louvered vents on the front door and side panels, sealed gasket around the door frames and brush strips around cable access points prevent dripping water, oil and airborne contaminants from getting inside. You can replace the air filter with standard, off-the-shelf furnace filters. Four high-performance intake fans built into the front door pull filtered air through the cabinet to keep your equipment cool. The cabinet swings away from the wall on a sturdy hinge, allowing easy back-door access to equipment and cabling during installation and maintenance. The reversible doors can open left or right. The doors and side panels lock securely to help prevent damage, tampering or theft. Convenient ports on the back door allow easy cable routing. The SRW12USNEMA comes fully assembled and ready to mount to the wall. Square and threaded mounting holes and numbered rack spaces make equipment installation easy. The vertical mounting rails adjust in 7/8-inch increments to house equipment up to 20.5 inches deep, such as network switches and patch panels.- Maximum load capacity of 90 kg (200 lb)- NEMA 12 (IP54) rating against dirt, dust, drips and splashes- Swings away from wall on hinge for easy back-door access- Locking steel cabinet with built-in ventilation fans- Secures 12U of 19 in. rack equipment up to 20.5 in. deep- Perfect for factories, construction areas, utility plants, power stations, transportation terminals, distribution hubs, warehouses and other harsh, dirty work environments where you need equipment to be secure, organized, out of the way and protected from environmental contaminants- Houses EIA-standard 19 in. rack equipment in 12U of space- Maximum load capacity of 90 kgs (200 lbs) - Built-in air filter, louvered vents and sealing door gaskets keep out dirt, dust, lint, oil, drips and splashes - Removable air filter can be replaced with standard, off-the-shelf furnace filters- Built-in high-performance door fans plug into standard NEMA 5-15R outlet (1.83 m (6-ft.) power cord included)- Sealed cable ports maintain dust and moisture resistance- Hinged Cabinet for Convenient Access: Swings away from the wall to allow easy back-door access to equipment and cabling during installation and maintenance - Reversible doors can open left or right to accommodate various rack configurations - Side panels and doors lock securely to help prevent damage, tampering or theft - Vented panels and built-in fans provide generous airflow to keep equipment cool - Convenient ports with removable covers and protective brush strips allow cable routing through rear door- Ships fully assembled for quick installation- Mounts to wall or rolls on floor with Tripp Lite’s optional SRCASTER caster kit - Wall-mounting holes spaced 16 in. apart for standard wall stud placement - Vertical mounting rails adjust in 7/8 in. increments to accommodate equipment up to 20.5 in. deep, such as network switches and patch panels- Rails adjust easily—unscrew them, slide them to desired depth, and screw them back in- Rails support square-hole or threaded-hole mounting - Rack spaces numbered for easy reference- Provides physical equipment and media security required for PCI DSS (Payment Card Industry Data Security Standard) compliance

"Saves Space and MoneyCombines an 8-port KVM switch, 19"" LCD screen, full keyboard and touchpad in a 1U rack-mountable drawerMounts into 19""-wide rack, 26""-38"" deepControl up to 8 servers from a single, easily accessible console – ideal when rack space is at a premiumIncludes eight P778-Series cables that support computers with either PS/2 or USB connectionsFlip-up/fold-down screen keeps the console from blocking access to rack equipment when not in useEliminates need to buy costly separate monitors, keyboards and mice for each computer/serverSimplifies IT TasksSwitch easily between the 8 ports via on-console buttons, on-screen display or hot keys; OSD can be set to English, Spanish, French, German or JapaneseHot pluggable; add or remove computers without having to power down the switchAuto-scan mode automatically sequences through all active ports that are accessible to the userLarge 19"" LCDExtra-wide display makes multitasking easierSupports video resolutions up to 1280 x 1024DDC emulation allows optimal output to the LCDMulti-Level Password SecurityEnhances security by limiting access to an administrator and up to 4 local usersTwo-level log-out allows for manual log-out or automatic log-out after a user-defined period of time has passedExpandability and Long-Lasting ReliabilityIncrease the number of connected computers up to 256 by daisy-chaining up to 31 B022-U08 KVM switchesA console cable kit is included so you can connect the external console port to a keyboard, mouse or monitor, or a B051-000 IP Remote Access UnitAn additional USB port on the front of the unit lets you connect an external USB mouse; a USB port is also available to share a peripheral such as a flash drive or external hard drive with all the connected serversCompatible with all major operating systems for easy integration into your existing structureFirmware is upgradable with included cable and utilityHeavy-duty steel housing stands up to frequent use"

The SmartRack® SRLADDERATTACH allows an overhead cable ladder (SRCABLELADDER) to be attached to a 2-post rack (SR2POST) or 4-post rack (SR4POST) and terminate on the wall. SRLADDERATTACH includes all hardware needed to create two connections (the ladder to one rack and the wall or from one rack to another). When connecting to the 2-post or 4-post racks, they can be attached either parallel with the rack structure or perpendicular to the rack structure.

The SR2319ADAPT Mounting Adapter Kit allows you to mount 19-inch rack equipment in a 23-inch rack. Attach the adapter brackets to the rack's vertical mounting rails using the included hardware. Then, attach 19-inch equipment to the brackets using the included hardware or your own. The cold-rolled steel brackets support a maximum load capacity of 20 lbs (9.1 kgs).

Fixed Shelf, 1U Cantilever mount, Cold rolled steel with black finish. Required mounting hardware included. Supports up to 30 lbs (13.6 kgs). Uses two shelves back to back to create a deep, fixed shelf in 2POST racks.

"UPSHDEARKIT front-mount support bracket system accommodates 2U UPS systems in 4-post rack-mount applications by using only the front vertical rails of the cabinet. Two included ""L bracket"" mounting ears offer front support of any 2U rack-mount chassis up to 65 pounds."