Showing 0–10 of 120 results

NetAlly G3-PWRADAPTER AC

Trendnet TC-NT2 network analyzer Blue, White

The T012-001-K Multi-Function Cable Tester is an essential tool for cable installers or anyone working in telecom or LAN environments. It allows you to track cable, find a short or breakage in non-powered wires, and perform wire mapping on RJ45 cables, detecting shorts and open wires. Powered by included 9-volt batteries in the main tester and remote probe unit, the T012-001-K can find an RJ11, RJ45 or BNC cable nestled within a group of cables. The probe unit’s LED flashlight is handy for working in dark areas. Included headphones help you work in noisy environments. An adjustable volume button lets you fine-tune the tone generator.

NetAlly LinkRunner AT 3000 PoE tester Black, Green

"StarTech.com REMOTETEST. Width: 4.33"" (110 mm), Depth: 7.09"" (180 mm), Height: 0.984"" (25 mm). Master (outer) case width: 13.4"" (340 mm), Master (outer) case length: 21.3"" (540 mm), Master (outer) case height: 13.4"" (340 mm)"

Essential Tool for Cable Installers or Telecom/LAN PersonnelThe N044-000-R allows you to test wiring continuity for Cat5, Cat6, telephone and coax cable assemblies at the press of a button. A combination of main tester unit and removable remote tester unit, the N044-000-R identifies crossed wires, short circuits and open circuits in BNC, F, RJ11, RJ12 and RJ45 cables. When not in use, the two-piece set can be stored in its vinyl carrying case to protect it from being damaged inside a crowded toolbox. Requires one 9V battery (not included) to operate.

The all-in-one T020-001-PSF Multi-Function Optical Fiber Cable Tester is an essential tool for cable installers or anyone working in telecom or LAN environments. The combination power meter/light source/visual fault locator allows you to test fiber optic cables for breaks, insertion loss and optical power loss up to 20KM. Featuring FC connectors with optional SC, ST and LC adapters, the T020-001-PSF gives you peace of mind and the ability to test a wide range of fiber cables, up to 20km, commonly installed in todays network infrastructures.The power meter supports 850 nm, 1300 nm, 1310 nm, 1490 nm, 1550 nm and 1625 nm wavelengths, while the light source supports 1310 nm and 1550 nm wavelengths. The visual fault locator features multiple frequency settings for continuous and flashing modes. The easy-to-read LCD interface displays power loss measurement data, wavelength, frequency, battery capacity and battery charge status.Three AA batteries are included, and the auto-off function preserves battery power. If you’re using rechargeable AA batteries, the USB Micro-B port charges them via connection to a USB wall charger or a computer’s USB port. When not in use, the T020-001-PSF can be stored in its handy carrying case.

The all-in-one T016-004-K Network Installer Tool Kit contains essential tools for cable installers or anyone working in telecom or LAN environments: cable tester, crimping tool, LSA punchdown tool and stripper tool. The cable tester allows you to test wiring continuity for Cat5, Cat6, Cat6a and telephone cable assemblies at the flip of a switch. A combination of main tester unit and removable remote tester unit, the cable tester identifies a connection, no connection, short circuit or open circuit. The tester features modes for fast and slow flashing of LEDs during automatic testing. When not in use, the four-piece T016-004-K can be stored in its handy carrying case.

This N844-LOOP-12F MTP/MPO OM3 Fiber Optic Loopback Tester is typically used for test and measurement procedures in networking environments.The device is ideal for a multitude of applications that require signal looping in a MTP/MPO form factor. Features push-pull tab for easy disconnect. A dust cap is included for protection during storage.

NetAlly LinkRunner AT 4000 PoE tester Black, Green