Showing 570–580 of 9438 results

Specify an SRSR for easy rear access to equipment connections in millwork, cabinets and flush in-wall installations. Available with a 19” or 23” useable depth, the SRSR system extends and rotates 90º in either direction, making it ideal for smaller systems.

Specify an SRSR for easy rear access to equipment connections in millwork, cabinets and flush in-wall installations. Available with a 19” or 23” useable depth, the SRSR system extends and rotates 90º in either direction, making it ideal for smaller systems.

"Designed to provide the same cable management facilities as our standard riser bases the SRB Series riser bases have been seismic certified to the following codes and standards: 2007 & 2010 CBC; 2006, 2009 & 2012 IBC; ASCE 7-05 (2005 Edition) & ASCE 7-10 (2010 Edition) and the 2006 & 2009 editions of NFPA 5000 for use in areas of high seismicity – Zone 4 or Seismic Design Category (SDC) “D”. These are designed for Mission Critical and/or High-Importance Installations in locations with the highest level of seismicity and top floor or rooftop installations including those within UBC and CBC Essential facilities or IBC, ASCE 7, and NFPA 5000 Seismic Use Group III facilities. For all codes, the Importance factor (Ip) is 1.5. Seismic Certified load capacity of 1,000 lbs (1 Bay), 1,750 lbs (2 Bay), and 2,450 lbs (3 Bay) when used with the appropriate seismic floor anchor brackets. With a standard 24"" height (custom heights from 9""-24""available upon request), these riser bases are constructed of rugged 11-gauge steel. OSHPD approved for fixed equipment anchorage in California healthcare facilities. Available for select enclosures, these riser bases require the use of seismic brackets."

Vent blockers are used to prevent the recirculation of hot air between top-mount fans and nearby vent openings. Vent blockers should be placed over the enclosure’s vents located on the upper front of the enclosure and upper sides. This will ensure that heated enclosure air will be forced out through the top-mounted exhaust fans instead of re-circulating, keeping equipment cool.

Vent blockers are used to prevent the recirculation of hot air between top-mount fans and nearby vent openings. Vent blockers should be placed over the enclosure’s vents located on the upper front of the enclosure, upper sides, and upper rear door (depending on enclosure). This will ensure that heated enclosure air will be forced out through the top-mounted exhaust fans instead of re-circulating, keeping equipment cool.

Designed to organize and protect cabling between racks. Smooth, steel cable fingers are placed in rackspace increments for complete control of access locations.

Offered in lightly smoked plexiglass, fully vented, vented plexi, large perforated vented and solid configurations. Beveled corners provide a stylistically modern appearance, while hinging either left or right. Large perf door has 64% open area, regular perf vented doors have 25% open area. Black textured powder coat finish. Includes keylock.

Offered in lightly smoked plexiglass, fully vented, vented plexi, large perforated vented and solid configurations. Beveled corners provide a stylistically modern appearance, while hinging either left or right. Large perf door has 64% open area, regular perf vented doors have 25% open area. Black textured powder coat finish. Includes keylock.

"SRSR Series 19"" Rotating Sliding Rail System. Specify an SRSR for rear access to equipment connections in millwork and cabinets. Available with a 19"" or 23"" useable depth, the SRSR system extends and rotates 90(0) in either direction, making it ideal for smaller millwork and in-wall installations.- Pulls out and rotates for equipment servicing- NEW Removable rack frame allows in-shop integration and on-site installation of equipment, saving time in the field- Simplifies equipment installation in cabinet- Shortens installation & service time- Available in 19"" and 23"" useable depths- Available from 12 space (21"") to 24 space (42"")- Integral cable management system provided- Locks in place at 0, 60, and 90 positions for easy installation and servicing- Ball bearing slides allow smooth rollout- Locks closed with included hardware- Up to 300 pound weight capacity, depending on model"

Specify an SRSR for easy rear access to equipment connections in millwork, cabinets and flush in-wall installations. Available with a 19” or 23” useable depth, the SRSR system extends and rotates 90º in either direction, making it ideal for smaller systems.