Showing 4900–4910 of 29094 results

The HDMI Mini Female to HDMI Male Adapter is the perfect solution for repurposing an HDMI Mini cable for use with a HDMI source device or display. The adapter is compact and designed for minimal signal loss. The passive design of this coupler allows it to support video resolutions of up to 1080p.

The DisplayPort Female to Female Coupler is the perfect solution for combining two DisplayPort cables to achieve connectivity over a longer distance. The coupler is compact and designed for minimal signal loss. The passive design of this coupler allows it to support video resolutions of up to 1080p.

This Slim Aux 3.5mm cable is designed with your mobile life in mind. The slim connector allows for easy connection into the headphone port of you mobile device while it is still in its protective case. The cable can then be plugged into a car stereo, headphone port or Aux port for audio on the go.

Replace your overused or lost computer power cable, or just keep and extra cord for convenience or travel. This computer power cable is designed to work with computers that use the 3-pin shroud power connector. Plus this heavy duty 18 AWG cord construction features a fully molded design for maximum durability and long life. This cable is the perfect length for allowing flexible placement and use of a computer.

"Velocity™ ""RCA"" Video Interconnects from Impact Acoustics ensure vivid picture quality and maximum detail from your composite video sources. These cost-effective high-performance cables have a real performance advantage over the cheap “give away” cables included with many consumer electronics products. The low-loss 75-ohm oxygen-free copper conductor and foamed PE dielectric maintain proper characteristic impedance, and guarantee that you will experience all the picture quality and performance your equipment can deliver. An OFC braid shield protects against radio frequency interference (RFI) and electromagnetic interference (EMI). A flexible jacket and 24K gold-plated heavy-duty contacts provide a lifetime of quality."

Today's mission critical advanced Fast Ethernet and Gigabit computer networks require the stability and reliability of Enhanced Category 5 high-speed cabling to distribute data, voice and video. To protect your high-speed network from noise and electromagnetic interference, use Cables To Go's Shielded Enhanced Cat5 Patch Cables. Each cable meets all Cat 5e TIA/EIA standards. The molded boot provides extra strain-relief and durability. Cables To Go Shielded Enhanced Cat5 Patch Cables are available in a variety of colors to easily color-code your network installation. - Connector: Shielded 50-micron gold plated RJ45 Male to Male - Conductor: 4-pair 24 AWG Stranded STP - Jacket: PVC - Molded boot provides extra strain-relief and durability - Foil shielding with drain wire - Applications: - 1000 BASE-T; 100 BASE-T; 10 BASE-T (IEEE 802.3) - 4/16 Mbps Token Ring (IEEE 802.5); 100 VG-AnyLAN - 100 Mbps TP-PMD (ANSI X3T9.5); 55/155 Mbps ATM - Voice - Designed For: Network Adapters, Hubs, Switches, Routers, DSL/Cable Modems, Patch Panels and other twisted-pair applications in high-noise environments - Wired: TSB 568B (AT&T 258A) - Certifications: TIA/EIA

"Fast, fast, fast - the three words that describe Cables To Go's Cat6 network cables. Perfect for distributing data, voice and video, these 550MHz rated patch cables ensure you always have the necessary throughput to handle today's and tomorrow's bandwidth-intensive applications. Each cable is fully tested and quality inspected, ensuring all EIA/TIA Cat 6 TIA/EIA- 568-B-2.1, draft 9 standards are met. Note: These cables are for 10/100 ethernet only and wil not work for gigabit ethernet since only two pairs of this cable are crossed.Cat6 patch cords from Cables To Go drastically reduce both impedance and structural return loss (SRL) as compared to standard 100 Mhz wire, which ensures error-free transmission! Constructed with high-quality cable and a shortened body plug, this design will keep Near-End Crosstalk (NEXT) levels to a minimum.Our all-new molded, snag-free ""clip"" prevents unwanted cable snags during installation without impairing your ability to insert and remove the connector from the port. It also provides unparalleled strain-relief, so that the cable is not damaged even when pulled on excessively.- Connector: 50-micron gold plated RJ-45 Male to Male- Conductor: 24 AWG Stranded Copper- Jacket: PVC- All-new molded, snag-free boot prevents unwanted cable snags while providing easy insertion and extraction from network ports- Crossed pin configuration allows you to connect two computers ""peer-to-peer"" without the need for a hub or switch- Perfect for connecting network switches and hubs without an uplink port to other switches and hubs"

"Fast, fast, fast - the three words that describe Cables To Go's Cat6 network cables. Perfect for distributing data, voice and video, these 550MHz rated patch cables ensure you always have the necessary throughput to handle today's and tomorrow's bandwidth-intensive applications. Each cable is fully tested and quality inspected, ensuring all EIA/TIA Cat 6 TIA/EIA- 568-B-2.1, draft 9 standards are met. Note: These cables are for 10/100 ethernet only and wil not work for gigabit ethernet since only two pairs of this cable are crossed. Cat6 patch cords from Cables To Go drastically reduce both impedance and structural return loss (SRL) as compared to standard 100 Mhz wire, which ensures error-free transmission! Constructed with high-quality cable and a shortened body plug, this design will keep Near-End Crosstalk (NEXT) levels to a minimum. Our all-new molded, snag-free ""clip"" prevents unwanted cable snags during installation without impairing your ability to insert and remove the connector from the port. It also provides unparalleled strain-relief, so that the cable is not damaged even when pulled on excessively. - Connector: 50-micron gold plated RJ-45 Male to Male - Conductor: 24 AWG Stranded Copper - Jacket: PVC - All-new molded, snag-free boot prevents unwanted cable snags while providing easy insertion and extraction from network ports - Crossed pin configuration allows you to connect two computers ""peer-to-peer"" without the need for a hub or switch - Perfect for connecting network switches and hubs without an uplink port to other switches and hubs"

Product Features- Connect the USB-Micro B port of a smartphone, tablet or other mobile device to a USB Type-C port- Designed to support USB 2.0 communication and features- Backwards compatible with USB 2.0 and USB 1.1 devices- Color coded white and labeled to designate USB 2.0 feature supportProduct DescriptionThis USB 2.0 USB-C to USB-Micro B cable is the perfect solution for connecting a smartphone, tablet, or other device that has a USB-Micro B port to a computer, tablet or other device that has a USB Type-C port for USB 2.0 communication. The color coded USB Type-C connector allows this cable to be easily identified as a USB 2.0 cable and differentiated from other cables which may support a different feature set. The USB Type-C connector is smaller than traditional USB connector and features a symmetrical design which allows it to be easily connected on the first try. Additionally, the durability of the USB Type-C connector allows for up to 10,000 connection cycles. This cable supports a data rate up to 480Mbps for data transfer and sync with 5 volts and 1 amp of power for device operation and charging.

"Fast, fast, fast - the three words that describe Cables To Go's Cat6 network cables. Perfect for distributing data, voice and video, these 550MHz rated patch cables ensure you always have the necessary throughput to handle today's and tomorrow's bandwidth-intensive applications. Each cable is fully tested and quality inspected, ensuring all EIA/TIA Cat 6 TIA/EIA- 568-B-2.1, draft 9 standards are met.Cat6 patch cords from Cables To Go drastically reduce both impedance and structural return loss (SRL) as compared to standard 100 Mhz wire, which ensures error-free transmission! Constructed with high-quality cable and a shortened body plug, this design will keep Near-End Crosstalk (NEXT) levels to a minimum.Our all-new molded, snag-free ""clip"" prevents unwanted cable snags during installation without impairing your ability to insert and remove the connector from the port. It also provides unparalleled strain-relief, so that the cable is not damaged even when pulled on excessively.- Connector: 50-micron gold plated RJ-45 Male to Male- Conductor: 24 AWG Stranded Copper- Jacket: PVC- All-new molded, snag-free boot prevents unwanted cable snags while providing easy insertion and extraction from network ports- Designed For: Network Adapters, Hubs, Switches, Routers, DSL/Cable Modems, Patch Panels and other twisted-pair applications- Perfect for Gigabit, Fast Ethernet, and Ethernet applications"