Showing 120–130 of 233 results

"Tripp Lite B120-000. Type: AV repeater, Maximum resolution: 2560 x 1600 pixels, Maximum transfer distance: 1800"" (45.7 m). AC input voltage: 100-240 V, AC input frequency: 50 - 60 Hz. Width: 2.4"" (61 mm), Depth: 2"" (50.8 mm), Height: 0.949"" (24.1 mm). Package width: 6.4"" (162.6 mm), Package depth: 2.2"" (55.9 mm), Package height: 7"" (177.8 mm). Master (outer) case width: 13.7"" (348 mm), Master (outer) case length: 8.7"" (221 mm), Master (outer) case height: 23.2"" (589.3 mm)"

The B126-1A0-U HDMI over Cat5/Cat6 Active Extender works with a B126-002 or B126-004 transmitter (sold separately) to extend an HDMI audio/video signal to an HDMI projector, monitor or television. It's ideal for digital signs, trade shows, presentations, classrooms, churches, retail settings and other applications where the video source is located farther than conventional cables allow. A latching HDMI connector on the built-in cable provides a more secure connectionThe receiver's built-in HDMI cable connects to the display. Cat5e/6 cable connects the receiver to the B126-Series transmitter (for best results, use 24 AWG solid-wire Cat5e/6 cable, such as the N202-Series). Power is supplied by the included USB Micro-B to USB-A cable, which connects between the receiver and a USB port on the display or a USB wall charger.The B126-1A0-U can extend a 1080p (@ 60 Hz) signal up to 125 feet (38.1 meters) with full, rich stereo. Built-in RJ45 LEDs indicate the units are receiving power and a signal from the source. Built-in equalization control lets you fine-tune the image quality at the display. Easy to set up with no software or drivers to install. Works with all operating systems and HDMI sources.

The B126-1A1SR HDMI over Cat5/Cat6 Extender Kit includes a transmitter unit and a receiver unit that work in tandem to extend HDMI audio and video, RS-232 serial and IR Remote Control signals to a projector, monitor or television. The kit is ideal for digital signs, trade shows, presentations, classrooms, churches, retail settings and other applications where the video source is located farther than conventional cables allow. How far you can extend the signals depends on the cable you use to connect the transmitter and receiver. You can extend a 3840 x 2160 (4K x 2K) Ultra High Definition (UHD) signal @ 24 Hz up to 328 feet (100 m) with a single Cat6a cable, up to 230 feet (70 m) with a 24 AWG solid-wire Cat6 cable (Tripp Lite’s N202-Series), and up to 150 feet (48 m) with a 26 AWG solid-wire Cat5e cable (N001- and N002-Series).For extending computer video resolutions of 1920 x 1200 @ 60 Hz or high-definition video resolutions of 1080p @ 60 Hz up to 328 feet (100 m), use a single 24 AWG solid-wire Cat5e/6 cable, such as Tripp Lite’s N202-Series. You can also control RS-232 serial devices, such as touchscreen displays or scanners, at baud rates up to 115 Kbps. The B126-1A1SR supports 7.1-channel surround sound, DTS-HD and Dolby TrueHD audio, as well as 3D video and HDCP. Easy to set up with no software or drivers to install. Mounts to a wall, rack or pole using the included hardware.- Extends a 3840 x 2160 (4K x 2K) signal up to 328 ft. (100 m)- Supports 7.1-channel surround sound, DTS-HD and Dolby TrueHD - Controls RS-232 serial devices at baud rates up to 115 Kbps- Works with all operating systems and HDMI video sources- Plug and play—no software or drivers to install- Extends High-Definition Signals: Extends a 3840 x 2160 (4K x 2K) Ultra High Definition (UHD) signal up to: 328 ft. (100 m) with a single Cat6a cable (custom-ordered from Tripp Lite) - 230 ft. (70 m) with a 24 AWG solid-wire Cat6 cable (N202-Series) - 150 ft. (48 m) with a 26 AWG solid-wire Cat5e cable (N001- and N002-Series)- Extends a computer video signal of 1920 x 1200 @ 60 Hz or HD signal of 1080p @ 60 Hz up to 328 ft. (100 m) with Cat5e/6 patch cable (N202-Series)Supports the Latest Video and Audio Resolutions Works with all operating systems and HDMI video sources- Supports 7.1-channel surround sound, DTS-HD and Dolby TrueHD audio- Supports 3D video and HDCP- 2-way 39 KHz IR Remote Control functionality lets you control your Blu-ray player with its remote while standing at the remote monitor (and vice versa)- RS-232 serial port supports 115 Kbps full-duplex baud rates for scanners and touchscreen monitors- Plug-and-play engineering—no software or drivers to download and install - Units connect quickly to source and display with HDMI cable (P568-Series)- Included mounting hardware lets you install each unit on a wall, rack or pole

The B140-101 is a DVI over Cat5 Passive Extender kit, which comes with both transmitter and receiver units. It transmits a DVI-D Single-Link signal up to 100 feet (30.5 meters) away using a single Cat5e/6 Ethernet cable. To achieve maximum distance and resolution, use 24 AWG Solid Wire Cat5e/6 cable (N202-Series). The B140-101 is compatible with all operating systems and is plug and play with no external power, software or drivers required.Compliant with the Federal Trade Agreements Act (TAA) for GSA Schedule purchases.Installation is simple. Connect the built-in DVI connector on the transmitter unit to the source. Connect the built-in DVI connector on the receiver unit to a display. Finally, the RJ45 ports on the transmitter and receiver units are connected using a single Cat5e/6 cable. A 1920 x 1080 at 60 Hz signal can be extended up to 50 feet (15.2 meters) from the source or a 1024 x 768 at 60 Hz signal up to 100 feet.

The B155-002-HD 2-Port Mini DisplayPort to HDMI Splitter converts and splits a Mini DisplayPort video signal for display on two HDMI-enabled monitors, projectors or televisions at the same time. Ideal for offices, conference rooms, retail settings, trade shows and classrooms, this compact splitter features a built-in Mini DisplayPort cable that connects to the source. It lets you use your existing HDMI displays instead of buying new Mini DisplayPort monitors or docking stations.The B155-002-HD supports video resolutions up to 1080p @ 60 Hz (1920 x 1080), as well as HDCP, EDID and DDC. Orange LEDs next to each output port indicate whether the splitter is powered on and transmitting a signal to the connected displays. The splitter works with all operating systems and is small enough to carry in your backpack or computer bag. Plug-and-play convenience means no software or drivers are needed. An included USB Micro-B cable connects between the source and the splitter to provide power, so no external power supply is required.

VGA Audio + Video, Serial and IR Control Signals over Cat5/6 CablingReceives IP-based audio + video transmitted point-to-point from a source 328 ft. away Add low-cost network switches between transmitter and receiver to continue extending distance up to 328 ft. per switchCreate a Multi-In, Multi-Out Installation Using B160-Series Transmitters and ReceiversConnect up to 64 transmitters and 255 receivers through multiple dedicated managed network switchesIGMP-enabled switches allow centralized control over which sources show on which displaysDisplays video from any analog or digital source, so you can mix and match technologies and use existing sources and monitorsEnhanced Technical FeaturesSupports video resolutions up to 1920 x 1440, including 1080pUses H.264 video compression standardTransmits on 20–60 kHz IR frequencyExtends IR control signals that control a source from a remote displaySupports RS-232 serial baud rates up to 57600 BpsHDCP and 3D compatible when used with a DisplayPort or HDMI transmitter Plug-and-Play FunctionalityNo software or drivers requiredHardware included for mounting on wall, rack or poleCompatible with all B160-Series A/V over IP transmittersTAA-CompliantCompliant with the Federal Trade Agreements Act (TAA) for GSA Schedule purchases

HDMI A/V, Serial and IR Control Signals over Cat5/6 CablingReceives IP-based audio/video transmitted point-to-point from a source 328 ft. away Add low-cost network switches between transmitter and receiver to continue extending distance up to 328 ft. per switchDual HDMI outputs for connecting 2 displaysCreate a Multi-In, Multi-Out Installation Using B160-Series Transmitters and ReceiversConnect up to 64 transmitters and 255 receivers through multiple dedicated managed network switchesIGMP-enabled switches allow centralized control over which sources show on which displaysDisplays video from any analog or digital source, so you can mix and match technologies and use existing sources and monitorsEnhanced Technical FeaturesSupports video resolutions up to 1920 x 1080 (1080p) @ 60 HzUses H.264 video compression standardTransmits on 20–60 kHz IR frequencyExtends IR control signals that control a source from a remote displaySupports RS-232 serial baud rates up to 57600 BpsHDCP and 3D compatible when used with a DisplayPort or HDMI transmitterPlug-and-Play FunctionalityNo software or drivers requiredHardware included for mounting on wall, rack or poleCompatible with all B160-Series A/V over IP transmittersTAA-CompliantCompliant with the Federal Trade Agreements Act (TAA) for GSA Schedule purchases

Tripp Lite's B165-101 RS232 Serial over Cat5 Extender Kit is a low cost solution that provides remote access and control of any RS232 protocol device. The B165-101 extends control of a serial device to over 1,000 meters ( 3280ft ). Supports full-duplex, 3 pin, data communication (signal ground, transmit data line, and receive data line).- Locates an RS-232 Serial device up to 304.8 m (1,000-ft.) from your system- Supports full-duplex, 3 pin, data communication (signal ground, transmit data line, and receive data line)- No software or drivers required...Plug-n-Play- Supported Baud Rates: 110, 1200, 9600, 38400, 57600, 115200 (max)

Tripp Lite High Speed Plug and Play USB 2.0 over Cat5 Extender Kit with 4-port hub, allows placement of USB hub up to 50 meters ( 164ft ) away from the source computer. Using solid conductor Cat5e rated cable, full 480mbps transmission speed is maintained the entire distance. Ideal for any situation where up to four USB devices need to be located more than the maximum 5 meter distance allowed by the USB timing signal. Also see B203-101-PNP for single device extension. For Solid Conductor patch cables, see tripp Lite N202- series patch cables.Key Features- Kit includes Transmitter and 4port Hub Receiver- Up to 50 meters ( 164ft ) distance over Solid Conductor Cat5e/Cat6 cable- Supports high speed data transfer rates up to 480mbps- Plug and Play...no Drivers or Software required- Backwards compatible to USB 1.1- Windows and MAC compatible- Compliant with the Federal Trade Agreements Act ( TAA ) for GSA Schedule purchases

The BHDBT-K-E3SI-ER HDBaseT HDMI over Cat5e/6/6a Extender Kit extends uncompressed HDMI audio and video, RS-232 serial and IR remote control signals up to 152.4 m (500-ft.) over a single Cat5e/6/6a cable, including a 1920 x 1080 (1080p) signal @ 60 Hz. In addition to HDMI, RS-232 and IR signals, this extender kit features three built-in 10/100 Ethernet ports on both the transmitter and receiver units. This allows connected devices, such as a Blu-ray™ player, cable/satellite box, and HDTV, to communicate with each other and access online content via LAN. You can also control RS-232 serial devices, such as touchscreen displays or scanners, at baud rates up to 115 Kbps. The two-way IR remote control feature (@ 39 KHz) lets you control your Blu-ray player using its remote when at the remote monitor or control your remote monitor using its remote when at the Blu-ray player. Locking HDMI ports (ideal for use with Tripp Lite’s P569-006-LOCK high-speed HDMI cables with locking connectors) on both the transmitter and receiver prevent cables from coming loose or undone, ensuring an intact signal. The plug-and-play BHDBT-K-E3SI-ER supports 7.1-channel surround sound, DTS-HD and Dolby TrueHD audio, as well as 3D video, EDID and HDCP.- Ideal for digital signs, classrooms and trade show booths- Built-in 10/100 Ethernet ports on transmitter and receiver- Extends a 1920 x 1080 (1080p) signal up to 152.4 m (500-ft.)- Supports 7.1-channel surround sound, DTS-HD and Dolby TrueHD- Controls RS-232 serial devices at baud rates up to 115 Kbps- Ideal for digital signage, classrooms, retail locations, conference rooms and trade show booths- Extends a high-definition 1920 x 1080 (1080p) @ 60 Hz signal up to 152.4 m (500-ft.)- Supports 7.1-channel surround sound, DTS-HD and Dolby TrueHD audio- Supports 3D video, EDID and HDCP- Reduces cable clutter and installation costs- Allows connected devices to communicate with each other and access online content via LAN- 2-way 39 KHz IR remote control functionality lets you control your Blu-ray player with its remote while standing at the remote monitor (and vice versa)- RS-232 serial port supports 115 Kbps full-duplex baud rates for scanners and touchscreen monitors- Plug and play with no software or drivers to download and install- Included mounting hardware for installing each unit on a wall, rack or pole- Prevent cables from coming loose or disconnected, ensuring an intact signal